Technical Features

● : Standard ○ : Option

Feature	Description	Remark
Full collective selective	In automatic running or attendant state, this function enables the elevator to respond both car calls and hall calls. Passengers at any service floor can call the elevator by pressing the up call button and down call button.	●
Anti-nuisance function	The system automatically judges the number of passengers in the car and compares it with the number of registered car calls. If there are excessive car calls, the system determines that it is nuisance and cancels all car calls. In this case, passengers need to register correct car calls again.	○
Car Call Cancellation	Passengers can press the button consecutively twice to cancel wrong calls.	●
Turn Off of Car Light and Fan	If there is no running command within the set time, the system automatically cuts off the power supply to the lamp and fan in the car.	●
Full-load direct runnung	When the car is full-loaded in automatic running state, the elevator does not respond to hall calls from the passing floors. These hall calls, however, can still be registered, and will be executed at next time of running (in the case of single elevator) or by another elevator (in the case of parallel/group control).	●
Overload protection	When the car load exceeds the rated elevator load, the elevator alarms and stops running.	●
Button stuck check	The system can automatically identify whether a hall call button is stuck and cancel the stuck call, preventing the condition that the elevator cannot close and run due to stuck hall calls.	●
Repeat door close	If the door lock is not applied after the elevator performs door close for a certain time, the elevator automatically opens the door and then closes the door again.	●
Automatic door open upon door lock abnormality	If the system detects that the door lock circuit is abnormal during door open/close, the elevator automatically opens and closes the door again, and reports a fault after the set door open/close times is reached.	●
Door open time setting	The system automatically determines different door open time for door open for call, command, protection, or delay according to the set door open holding time.	●
Arrival gong disabled at night	Within the set time period, the arrival gong is disabled.	○
Landing at another floor	If the door open time exceeds the door open protection time but the door open limit signal is still inactive, the elevator closes the door and then automatically runs to the next landing floor.	●
Voice Announcement	The elevator automatically announces information such as the running direction and next arriving floor during running.	●
Forced door close	When the door fails to close within the set time due to the action of the light curtain or safety edge, the elevator enters the forced door close state, closes the door slowly, and gives a prompt tone.	○
Parallel / Croup control	The system supports parallel control of two elevators / group control of more than three elevators.	○
Micro Leveling	After landing at a floor, the elevator may move upward or downward due to the load change and the car door is not aligned with the ground, which is inconvenient for in and out of passengers and goods. In this case, the system allows the elevator to run to the leveling position in the door open state at the leveling speed.	○
Light curtain signal judgment	If the door is blocked by stuff during door close, the light curtain acts and the elevator opens the door. This function is invalid in fire emergency state.	○
Power failure emergency evacuation	For the elevator configured with standby power supply, the system uses the standby power supply (ARD System) to implement low-speed self-rescue in the case of power failure.	○
Residential monitoring	The control system can be connected to the terminal in the monitoring room. By using the NEMS software, you can view the floor position, running direction, and fault state of the elevator.	○
Parking Operation	In order for park the elevator, if the parking key is on position the car stop at the specified floor after finish servicing of all of registered call. After the car stops at the specified floor, the car light and fan are off automatically and every buttons both on the car operating panel and hall button box are no more available.	○
Fire return Operation	In case of fire every cars should be returned to the specified floor in order to evacuate passengers safety.	○
Fireman Operation	In case of fire, a fireman can use the elevator which is stopped at the specified floor in order to support fireman for fire-fighting.	○